Welcome to the DeeperBlue.com Forums, the largest online community dedicated to Freediving, Scuba Diving and Spearfishing. To gain full access to the DeeperBlue.com Forums you must register for a free account. As a registered member you will be able to:
You can gain access to all this absolutely free when you register for an account, so sign up today!
Yes, the "Dreamloader" would have quite a lot of loose cord hanging around in the water due to the increased draw lengths of the handles using this pulley system. The intention was that the user could wind up any excess cord lengths around each of the plastic handles before moving on to the next pull on the loading handles during the step-wise gun cocking process. However I have been told there will be another version of the "Dreamloader" where excess cord will be automatically gathered up by the handles. I do not have any details except that a potential name for this new version is the "Dreamloader Automatic".In the sea or ocean with these ropes there will be many problems.
But the idea of "Dreamair" I like.
Shoots "Dreamair" good!
Good luck to the guys!
It is interesting to hear their opinion.I know that some divers have evaluated the guns in the ocean,.
The "Dreamloader" works in the same way as the device shown in this crossbow video. Note that the loading handle draw is longer than the draw of the crossbow as the loading device cord "doubles up", being anchored on the rear stock of the crossbow and running forwards to the front end of the crossbow before running rearwards again. The "Dreamloader" anchors on the shaft as it is locked in the gun by the trigger mechanism, unlike a crossbow which grasps the bowstring rather than the projectile or bolt.In fact, there is a new underwater weapon very rarely.
I think a lot of lovers of spearfishing will have a desire to try it on the hunt.
I also thought about such a project.
With the same scheme: open harpoon and pneumatic drive can be different ways of charging it. But I'm very confused by the idea of charging "Dreamair"
This is charging a land crossbow.
that in the water can be uncomfortable.
I think the divers are sworn to secrecy, as otherwise they would not have been given a gun. A good reason to keep one's mouth shut is that by doing so they may get to keep their gun!It is interesting to hear their opinion.
Such publications are possible?
You can hear the guns shooting on the video, it actually sounds like a pneumatic as you can hear a sort of clunk, but it is not as loud as some of my pneumatic guns are.This is all really exciting news. I have never considered anything else than a rubber band gun. But this creation could change my mind. I guess I am one of those people who are always welcoming exotic finely crafted things.
How loud you think this gun will be compared to band and pneumatic guns?
Sent from my iPhone using Tapatalk
I finally got my old ID back after sending the "password recovery" system a different email address, having the same address as popgun pete R was evidently too much for it!! Anyway I can comment on myself now and say that the winding drums, axles, etc. will still be in aluminium in the new "Dreamair" gun, but everything else will be in carbon fibre. I suppose titanium could also be included at some stage, but although lighter than stainless steel it is expensive stuff and heavier than aluminium.I know that some divers have evaluated the guns in the ocean, so I think any delay has been due to working out how to make the gun as efficiently as possible. For example the machined winding drums could be molded if you had a strong enough material to do the job, that would eliminate the cost of machining each one. They need a strong anchor point for the cables and track grooves that will not strip their flanges, but if these requirements were met then they could be churned out, say in a reinforced composite material. Tooling up would be expensive, but once done these parts could be mass produced very quickly.
I think the divers are sworn to secrecy, as otherwise they would not have been given a gun. A good reason to keep one's mouth shut is that by doing so they may get to keep their gun!
I finally got my old ID back after sending the "password recovery" system a different email address, having the same address as popgun pete R was evidently too much for it!! Anyway I can comment on myself now and say that the winding drums, axles, etc. will still be in aluminium in the new "Dreamair" gun, but everything else will be in carbon fibre. I suppose titanium could also be included at some stage, but although lighter than stainless steel it is expensive stuff and heavier than aluminium.
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?